Products
35 products
Sort by:
35 products
Aluminium finish — clean and professional transition for every external corner
Designed exclusively for the EUBIQ SH1 trunking, this 90° external corner with an aluminium finish ensures a clean, solid, and discreet joint. Tool-free assembly, impeccable look: it blends in perfectly once installed.
Why choose a dedicated corner piece?
Perfect fit
Genuine part perfectly sized for the SH1 trunking. Zero play, zero misalignment: a precise, millimetric fit.
Protected cables
Unlike DIY cuts, there are no sharp edges to threaten the insulation of your electrical or network cables.
Tool-free installation
Simply snaps onto the trunking sections. No special tools required in the majority of configurations.
Aluminium finish
Elegant matte appearance, corrosion-resistant. Integrates discreetly into all professional and residential environments.
DIY cut vs. genuine corner
- Sharp edges dangerous for cables
- Imprecise joints and unsightly gaps
- Time-consuming (cutting, fitting, corrections)
- Unattractive look devalues the installation
- Smooth and safe surfaces
- Precise, gap-free fitting
- Installed in seconds
- Immediate professional result
Technical specifications
This corner is designed exclusively for SH1 trunking. It will not be compatible with other trunking references or brands. Double-check your trunking reference before purchasing.
Where to use it?
Workstations and offices
Manage IT and electrical cable routing around partition or furniture corners.
Workshops and technical areas
Neatly contour room corners without leaving cables exposed.
Residential settings
External corner wiring for living rooms, bedrooms, or hallways with a discreet finish matching the trunking.
Commercial premises
Maintain a neat appearance in spaces visible to customers or the public.
4-step installation guide
Cut your trunking lengths
Ensure your two SH1 trunking sections are correctly cut at 90° (straight cut, not mitered).
Position the corner
Snap the SH1 external corner onto the end of each section. The piece is designed to fit without force.
Check alignment
Visually verify that both trunking sections are well-aligned and the corner is perfectly applied against the wall surface.
Secure if necessary
Depending on your configuration, secure the trunking to the wall according to the SH1 range recommendations (screws or adhesive, depending on the substrate).
Aluminium finish: discretion and durability
Aluminium does not rust, even in slightly damp environments.
Only 30 g for this piece, facilitating handling during installation.
The finish perfectly matches the rest of the SH1 range for a harmonious installation.
Neither too shiny nor too matte: aluminium fits into most interiors and work environments.
Frequently asked questions
Is this corner compatible with other EUBIQ trunking?
No. It is designed specifically for SH1 trunking. For other items in the range, check the compatible accessories mentioned on each product sheet.
Can the angle be adjusted to something other than 90°?
No, this corner is fixed at 90°. If your configuration requires a different angle, consider an adjustable corner, available separately in the EUBIQ range.
Do I need to buy an internal corner as well?
It depends on your trunking route. The external corner is for a protruding corner (the trunking goes "around" a corner). For an inside corner (the trunking goes into a recess), you need an internal corner.
Is this accessory sold individually?
Yes, it is sold individually. Count one corner per corner of your installation.
Additional information
A perfect corner for a perfect installation.
Install, snap: the result speaks for itself.
Perfect 90° transition for every wall corner
Dedicated fitting for inside corners: simple interlocking, impeccable finish, and continuous protection for your cables. Available in silver aluminum or matte black.
Why choose this internal corner?
Perfect continuity
Fluid and aligned transition for inside wall corners, with no need for cutting or rough DIY fixes.
Cable protection
Your electrical, air conditioning, or network cables remain protected and concealed, even in corners.
Two finishes
Silver aluminum for a technical look or matte black for discreet integration — the choice is yours.
Immediate installation
Simple interlocking onto the SH1 trunking, with no specialized tools required. Professional results in seconds.
Technical specifications
What is it suitable for?
Electrical installations
Routing electrical cables through the corners of rooms, offices, or workshops.
AC trunking corner
Ideal for neatly covering air conditioning pipes or cables in internal corners.
Network or TV cables
Neat concealment of multimedia, Ethernet, or HDMI cables along wall corners.
Professional premises
Restaurants, hotels, offices: a modern aluminum finish that integrates into any environment.
Installation in 5 steps
Position the SH1 trunking
Install the first section of trunking along the wall, up to the internal corner.
Interlock the internal corner
Clip the SH1 internal corner onto the end of the first trunking section.
Connect the second section
Insert the second trunking section into the other opening, perpendicularly.
Check alignment
Ensure everything is securely interlocked and held properly on the wall mount.
Route your cables and close
Route your cables through the trunking and close the cover. You're done.
This corner is designed exclusively for EUBIQ's SH1 trunking. It is not compatible with other references or brands of trunking. The corner is fixed (90°) and not adjustable.
Frequently asked questions
What is the difference between an internal and an external corner?
The internal corner is used when the trunking needs to turn in an inside wall corner ("hollow" angle). The external corner is designed for protruding corners. Depending on your wall configuration, you may need both types.
Is this corner compatible with other trunking brands?
No. This internal corner is specifically designed for the EUBIQ brand SH1 trunking. It will not be compatible with trunking from other manufacturers, even if dimensions are similar.
Can it be used for air conditioning trunking?
Yes, if you are using SH1 trunking to cover your air conditioning cables, this AC trunking corner is perfectly suited for internal wall corners.
Can the corner be adjusted to angles other than 90°?
No, this corner is fixed at 90° and cannot be adjusted. It is only suitable for standard right-angled corners.
Clean finish, quick installation, professional results.
The SH1 internal corner transforms every wall corner into a clean, controlled detail.
The modular accessory that clears your countertop
Designed exclusively for the EUBIQ SH1 power track, this 400 mm aluminum bar allows you to hang spatulas, ladles, and utensils directly beneath your track. Installs in seconds, with no screws and no drilling required.
Why choose this support bar?
Manufactured exclusively for the SH1 track, it slides in effortlessly without extra screws. No makeshift DIY required.
Keep spatulas, ladles, tongs, and other utensils within reach. Free up your drawers and countertop space.
A modern, timeless look that naturally integrates into any contemporary kitchen.
Combine it with other EUBIQ SH1 accessories: shelves, storage, integrated power sockets… The track adapts to your needs.
Technical specifications
Installation in 3 steps
Slide the ends of the support bar into the tracks provided on the EUBIQ SH1 track.
A simple click is all it takes to hold the bar firmly in place, with no extra screws or drilling.
Hang hooks, spatulas, ladles, or tongs directly onto the bar. Your countertop is cleared!
Tip: For even more effective organization, combine several EUBIQ SH1 system accessories: shelves, storage, integrated power sockets… The SH1 track is designed to adapt to your needs.
Who is this support bar for?
Looking to adopt a modern power track system and organize your kitchen efficiently? This bar is the essential accessory for your SH1 track.
Looking for a reliable, aesthetic solution for your clients? The EUBIQ SH1 modular system offers a premium finish and fast installation on-site.
- ✅ Ideal for kitchens with an existing EUBIQ SH1 track
- ✅ Perfect for optimizing space above the countertop
- ✅ Suitable for kitchens with limited floor or countertop space
- ✅ Compatible with standard kitchen bar hooks and accessories
Frequently asked questions
No. This accessory is specifically designed to integrate into the EUBIQ SH1 power track system. It cannot be used independently or with other trunking systems.
No, no additional drilling is required for the bar itself. It fits directly into the SH1 track already fixed to the wall.
It is designed to support standard kitchen utensils (spatulas, ladles, tongs, etc.). For information on maximum load capacity, please refer to the EUBIQ technical documentation.
Yes, the SH1 system is fully modular. You can position and combine several bars based on the length of your track and your needs.
Technical documentation
This accessory is a fixture and organization product. It is not an electrical safety device. For all electrical installations, please hire a qualified professional.
No more cluttered countertops: your utensils are within reach, elegantly hung with a modern aluminum finish.
A small accessory, a big daily change.
Add to cart
330 cm — Compatible with SH1 profile exclusively
Create a reliable physical separation between your power cables (230 V) and your data cables (RJ45, telephony, home automation) in one single trunking, in full compliance with the NFC 15-100 standard.
Why separate high voltage and low voltage?
Can you run high voltage and low voltage in the same trunking? Yes — provided you use an approved physical divider. Here is why it is essential:
NFC 15-100 Compliance
The standard requires a physical separation between power cables (230 V) and low-signal cables (RJ45, telephony, etc.).
Zero interference
High voltage cables generate electromagnetic interference that degrades your network, audio, or home automation connections.
Enhanced safety
Physical separation reduces risks in the event of a high-voltage cable failure inside the trunking.
Optimized installation
One single trunking is enough, without sacrificing order or safety. Space-saving and aesthetic results guaranteed.
EUBIQ flange features
Covers almost the entire standard floor-to-ceiling height or a common partition length, without intermediate connectors.
Lightweight, easy to handle and position on your own, even at height on a ladder.
Designed and dimensioned specifically for the SH1 profile. Check your reference before ordering.
5-step installation
Installation is simple and requires no specific tools. Direct manual insertion into the profile.
Ensure the SH1 profile is securely fixed to the wall or ceiling and that all cables are removed or have not yet been installed.
If your run is shorter than 330 cm, cut the flange to the correct size with a hacksaw or suitable wire cutters.
Slide it into the SH1 profile rail until it stops. It positions itself in the center of the trunking to create two sealed compartments.
High voltage side (230 V cables, power supply) on one side of the flange; low voltage side (RJ45, telephony, HDMI, home automation…) on the other.
Installation is complete, clean, and up to code. No screws or glue needed.
Who is this separator for?
Professional Electricians
- New electrical installations or renovations
- NFC 15-100 compliance upgrades for existing installations
- Wiring for offices and professional premises
DIY Enthusiasts
- Housing renovations with surface-mounted trunking
- Home automation or home network projects
- Workshop or garage wiring
Full technical specifications
| Feature | Value |
|---|---|
| Brand | EUBIQ |
| Length | 330 cm |
| Dimensions (L × W × H) | 330 × 2 × 1 cm |
| Weight | 300 g |
| Compatibility | SH1 profile exclusively |
| Usage | High voltage / low voltage separation |
| Target standard | NFC 15-100 |
Frequently Asked Questions
Important note: this product is an electrical installation accessory. Its implementation must comply with the electrical standards in force (NFC 15-100). If in doubt, call a qualified electrician. This product does not in itself constitute a certificate of conformity for your installation.
One trunking, two perfectly separated worlds.
With this 330 cm EUBIQ flange, finally reconcile practicality and electrical compliance.
Pair of end caps for RH1 and RH2 trunking
-
FeaturesEnd caps to be fixed to the ends of the RH trunking.
RH recessed trunking is ideal for offices, meeting tables and workstations. It combines elegant design and functionality, allowing for the creation of fully electrified furniture with various multimedia connectors. This RH power rail can be integrated into a table or a wall thanks to different installation methods.
-
Associated products
- RH1 Chassis
- RH2 Chassis
- SFC3 Power Segment
- Blanking Plate
- End Caps
- Separation Flange
- Separation Plate
- DS3 Housing
- DS4 Housing
Additional information
- Brand : EUBIQ
- Weight : 17 g
- Dimensions (L × W × H) : 9 × 4 × 1 cm
The pair — flawless finish from end to end
Neatly close off each end of your EUBIQ SH1 trunking. These brushed aluminum end caps snap on without tools or glue for an instant professional look. 25g of precision that makes all the difference.
Why end caps make all the difference
Well-installed trunking without end caps remains an unfinished project. These caps play both an aesthetic and protective role.
They hermetically seal the two open ends of the SH1 trunking, hiding the interior of the profile.
They protect cables from dust, impacts, and moisture at the ends of the trunking.
They provide a finished and professional look to your entire cable installation.
Perfectly adapted to EUBIQ SH1 trunking — no makeshift DIY required.
Technical specifications
What are they suitable for?
These caps fit into a wide variety of environments where SH1 cable trunking is used.
Concealing cables for TVs, internet boxes, hi-fi systems, for a living room or bedroom without visible wires.
Ideal for protecting hoses and cables of an air conditioning unit, with a discreet and durable aluminum finish.
To hide exposed pipes in a bathroom or kitchen, with a clean and neat look.
Offices, meeting rooms, commercial spaces: a clean cable installation reinforces the professional image of the space.
Installation in 3 simple steps
Ensure your SH1 trunking is correctly fixed to the wall or desired surface, with the cables inside.
Insert the end cap into one of the two open ends of the SH1 trunking. It fits precisely thanks to its custom-made design.
Repeat the process at the other end of the trunking. Your installation is now perfectly finished, from start to finish.
The pair: why it's essential
Trunking always has two ends. Therefore, these caps are systematically sold as a pair to save you from having to place a second order and to ensure a symmetrical result. A single item is enough to finalize your cable trunking installation, whether it is for interior wall trunking, exterior cable trunking, or specific uses like air conditioning pipe trunking.
Frequently asked questions
No, these caps are specifically designed for EUBIQ SH1 trunking. For other models, carefully check the reference of your trunking before ordering.
The brushed aluminum finish offers good resistance, but we recommend you verify the installation conditions of your SH1 trunking with the manufacturer for outdoor use exposed to the elements.
No. These caps snap directly onto the ends of the SH1 trunking, without additional fasteners.
The end cap closes the open ends of a trunking (start and end of the run). The joint cover is used to connect two sections of trunking together. These are definitely end caps.
Product summary information
Sometimes a single detail is enough to transform a decent cable installation into a truly professional result. Understated, precise, and designed to go unnoticed... while enhancing the whole setup.
Because a beautiful installation deserves a beautiful finish, right to the end.
Add to cart
Black coiled cable, stretched cable length: 2.4 M.
Additional information
- Brand: EUBIQ
- Weight: 300 g
- Dimensions (L × W × H): 32 × 14 × 1 cm
Black coiled cable, extended cable length: 1.2 M
Additional information
- Brand: EUBIQ
- Weight: 300 g
- Dimensions (L × W × H): 32 × 14 × 1 cm
Showing 8/35
NextCollections featured
The French specialist in designer electrical tracks since 2008. Exclusive Eubiq importer in Europe — Dilectro Ltd.
The French specialist in designer electrical tracks since 2008. Exclusive Eubiq importer in Europe — Dilectro Ltd.